现货促销CVGL72TP3 CTGR71TP1默克Millipore密理博Durapore滤芯CVHL72TP3

2024-07-30

默克Millipore密理博Durapore滤芯CVHL72TP3 CVGL72TP3 CTGR71TP1

有效去除胶体和颗粒污染物。Durapore滤芯在制造过程中进行了100%的完整性测试,以确保完整性。Durapore亲水滤芯由聚偏氟乙烯(PVDF)膜与纤维素酯(RW06)预过滤层制造,更大的通量和聚丙烯组件,广泛的化学相容性。

Description
Catalogue NumberCVHL72TP3
Trade Name
  • Durapore®

DescriptionDurapore® Cartridge Filter with prefilter 20 in. 0.45 µm Code 7

Product Information
Device ConfigurationCartridge
Maximum Differential Pressure, bar (psid)Forward: 5.5 bar (80 psid) @ 25 °C; 1.7 bar (25 psid) @ 80 °C; 0.35 bar (5 psid) @ 135 °C. Reverse: 3.5 bar (50 psid) @ 25 °C
Cartridge CodeCode 7 (2-226) O-rings w/locking-tabs
Good Manufacturing PracticesThese products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.
Prefilter MaterialMixed Cellulose Esters (MCE)
Quality LevelMQ400

Biological Information
Bacterial EndotoxinsAqueous extraction contains ≤0.5 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test
MediaDurapore® w/Prefilter
SterilityOther
Sterilization10 SIP cycles of 30 min or 10 autoclave cycles of 60 min @ 121 °C
WettabilityHydrophilic

Physicochemical Information
Pore Size0.45 µm
Air Diffusion at 23 °C≤30 mL/min @ 1.5 bar (22 psig) in water
Bubble Point at 23 °C≥1930 mbar (28 psig) air with water
Gravimetric ExtractablesThe extractables level was equal to or less than 45 mg per 10-inch cartridge after 24 hours in water at controlled room temperature.
Indirect Food AdditiveAll component materials meet the FDA Indirect Food Additive requirements cited in 21 CFR 177-182. All component materials meet the requirements of the EU framework regulation [1935/2004/EC] regarding materials and articles intended to contact food.
Non-Fiber ReleasingThis product was manufactured with a Durapore® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).
USP Bacterial EndotoxinsA sample aqueous extraction contains less than 0.5 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) test.

Dimensions
Cartridge Nominal Length20 in. (50 cm)
Diameter6.9 cm (2.7 in.)
Filtration Area1.38 m²
Device Size20 in.

Materials Information
Chemistry
  • Polyvinylidene Fluoride (PVDF)

Device Material
  • Polypropylene

Seal MaterialSilicone (SI)
Support MaterialPolypropylene

Packaging Information
Material Size3
Material PackageDouble Easy-Open bag

Specifications
Oxidizable SubstancesWill meet the USP Oxidizable Substances Test requirements after a water flush of ≥2 L

规格
OptiScale® and Millipak® Capsules
OptiScale® 25 CapsulesOptiScale® 47 CapsulesMillipak® 100Millipak® 200
Nominal Dimensions
Maximum length:39 mm (1.52 in.) with female Luer-Lok inlet/male Luer-Lok outlet82 mm (3.24 in.) with flange inlet/hose barb outlet74 mm (2.91 in.) with flange inlet/flange outlet94 mm (3.70 in.) with hose barb inlet/hose barb outlet13 cm (5.1 in.)15.5 cm (6.1 in.)
Diameter:31 mm (1.21 in)69 mm (2.75 in.)7.6 cm (3.0 in.)
Weight:0.19 oz (5.5 g)2.3 oz (67 g)
Filtration Area3.5 cm²17.7 cm²500 cm² (0.54 ft²)1000 cm² (1.08 ft²)
Materials of Construction
Filter membrane:Hydrophilic polyvinylidene fluoride (PVDF)
Structural components:PolypropylenePolycarbonate
Supports:PolypropylenePolycarbonate
Vent caps:PolypropylenePolyvinylidene fluoride (PVDF)
Internal seal rings:Fluoroelastomers
Housing VentCapped Vent with female Luer connections on inlet side of device.Adjustable vent with male luer and female Luer-Lok connections on inlet side of device.
Maximum Inlet Pressure4.1 bar (60 psig) at 25 °C5.5 bar (80 psig) at 25 °C5.2 bar (75 psig) at 25 °C
Maximum Differential Pressure
Forward:4.1 bar (60 psig) at 25 °C5.5 bar (80 psig) at 25 °C4.1 bar (60 psid) at 25 °C1.7 bar (25 psid) at 80 °C345 mbar (5 psid) at 123 °C
Reverse:0 bar (0 psig)0.7 bar (10 psig) at 25 °C690 mbar (10 psid) at 25 °C
Bubble Point at 23 °C≥ 1790 mbar (26 psig) air with water
Gravimetric ExtractablesAfter autoclaving and a 24-hour soak in ASTM Type 1 reagent grade water at controlled room temperature:
≤ 2.5 mg≤ 5.0 mg
Bacterial EndotoxinAqueous extraction containsAqueous extraction contains
Oxidizable SubstancesMeets the requirements of the USP Oxidizable Substance Test after a water flush of:
≤ 100 mL200 mL200 mL
TOC/ConductivityThis product exhibited less than 500 ppb TOC per USP<643>and less than 1.3 µS per USP<645>after autoclave and a WFI water flush of 15 mL.
SterilizationMay be autoclaved for 1 cycle of 60 minutes at 123 °CMay be autoclaved for 3 cycles of 60 minutes at 126 °CMay be autoclaved for 3 cycles of 90 minutes at 123 °C. Capable of 45 kilogray (4.5 Megarad) gamma exposure (cannot be steam sterilized in-line).
Good Manufacturing PracticesThese products are manufactured in a Millipore facility which adheres to FDA Device Good Manufacturing Practices.
Non-Fiber ReleasingDurapore membrane meets the criteria for a “non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).
Component Material ToxicityComponent materials meet the requirements of USP<88>Reactivity Test for Class VI Plastics. This product is non-toxic per the current USP<88>Safety Test.
Indirect Food AdditiveThe Durapore membrane used in these products meets the FDA Indirect Food Additive requirements cited in 21 CFR 177.2910. All other components meet the FDA Indirect Food Additive requirements cited in 21 CFR 177 – 182.
Opticap® XL Capsules and Cartridge Filters
Opticap® XL 2Opticap® XL 4Opticap® XL 5Opticap® XL 10Cartridge (per 10-inch element)
Nominal Dimensions
Maximum length:14.2 cm (5.6 in.)19.6 cm (7.7 in.)21.6 cm (8.5 in.)33.5 cm (13.2 in.)
Diameter:8.4 cm (3.3 in.)10.7 cm (4.2 in.)6.9 cm (2.7 in.)
Filtration Area0.09 m² (0.93 ft²)0.19 m² (2.09 ft²)0.35 m² (3.7 ft²)0.69 m² (7.4 ft²)
Materials of Construction
Filter membrane:Hydrophilic PVDF
Prefilter media:Mixed esters of cellulose
Film edge:Polypropylene
Structural components:Polypropylene
Supports:Polypropylene
Vent O-rings:Silicone
O-rings:Silicone
Vent/Drain¼ in. hose barb with double O-ring seal
Maximum Inlet Pressure5.5 bar (80 psi) at 23 °C2.8 bar (40 psi) at 60 °C1.0 bar (15 psi) at 80 °C
Maximum Differential Pressure
Forward:5.5 bar (80 psid) at 25 °C (with prefilter)1.0 bar (15 psid) at 80 °C (with prefilter)3.4 bar (50 psid) at 25 °C (without prefilter)5.5 bar (80 psid) at 25 °C1.8 bar (25 psid) at 80 °C345 mbar (5 psid) at 135 °C
Reverse:3.4 bar (50 psid) at 25 °C, intermittent3.5 bar (50 psid) at 25 °C, intermittent
Bubble Point at 23 °C≥ 1930 mbar (28 psig) air with water
Air DiffusionThrough a water wet membrane at ambient temperature at 1.5 bar (22 psi):Through a water wet membrane at 23 °C at 1.5 bar (22 psi):
≤ 4.5 cc/min≤ 7.5 cc/min≤ 15 cc/min
Gravimetric ExtractablesAfter autoclaving and a 24-hour soak in ASTM Type 1 reagent grade water at controlled room temperature:
With prefilter:≤ 50 mg≤ 45 mg
Without prefilter:≤ 10 mg≤ 15 mg≤ 25 mg≤ 20 mg
Bacterial EndotoxinAqueous extraction contains < 0.5 EU/mL as determined by the Limulus Amebocyte Lysate (LAL) Test.
Oxidizable SubstancesMeets the requirements of the USP Oxidizable Substance Test after a water flush of:
500 mL1000 mL
Sterilization (with Prefilter)
Autoclaved:3 cycles of 60 minutes at 121 °C.10 cycles of 60 minutes at 121 °C
Steam Sterilization:Cannot be steam sterilized in-line.10 cycles of 30 minutes at 121 °C
Hot Water Sanitization:30 cycles of 30 minutes at 80 °C
Sterilization (without Prefilter)
Autoclaved:3 cycles of 60 minutes at 126 °C30 cycles of 60 minutes at 126 °C
Steam Sterilization:Cannot be steam sterilized in-line.30 cycles of 30 minutes at 135 °C
Hot Water Sanitization:30 cycles of 30 minutes at 80 °C
Total Organic Carbon (TOC)/ConductivityAutoclaved filter effluent meets the WFI requirement of USP<643>, for Total Organic Carbon and USP<645>for Water Conductivity at 25 ºC after a WFI flush of 11.5 L
Good Manufacturing PracticesThese products are manufactured in a Millipore facility which adheres to FDA Good Manufacturing Practices.
Non-Fiber ReleasingDurapore membrane meets the criteria for a “non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).
Component Material ToxicityComponent materials were tested and meet the criteria of the USP<88>Reactivity Test for Class VI Plastics. Sterilizing-grade Durapore Filters are non-toxic per the current USP<88>Safety Test.
Indirect Food AdditiveDurapore membrane meets the FDA Indirect Food Additive requirements cited in 21 CFR 177.2910. All other component materials also meet the FDA Indirect Food Additive requirements cited in 21 CFR 177 – 182.
European Pressure Equipment DirectiveMillipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Equipment Directive, this product does not bear the CE mark.

CVHL01TP3 CVHL02TP3 CVHL03TP3 CVHL01PP3 CVHL02PP3 CVHL03PP3 CVHL51TP3 CVHL52TP3 CVHL53TP3 CVHL51PP3 CVHL52PP3 CVHL53PP3 CVHL71TP3 CVHL72TP3 CVHL73TP3 CVHL71PP3 CVHL72PP3 CVHL73PP3 CVHL75PP1 CTGR01TP1 CTGR02TP1 CTGR03TP1 CTGR71TP1 CTGR72TP1 CTGR73TP1 CTGR75S01 KTGRA02FF3 KTGRA02HH3 KTGRA02TT3 KTGRA04FF3 KTGRA04HH3 KTGRA04TT3 KTGRA05HH1 KTGRA05TT1 KTGRA10FF1 KTGRA10HH1 KTGRA10TT1 CVGL01TP3 CVGL02TP3 CVGL03TP3 CVGL51TP3 CVGL52TP3 CVGL53TP3 CVGL71TP3 CVGL73TP3 CVGL75S01 CVVL01TP3 CVVL02TP3 CVVL03TP3 CVVL51TP3 CVVL52TP3 CVVL53TP3 CVVL71TP3 CVVL72TP3 CVVL72TP3 CVVL75S01 CVDI01TPE CVDI02TPE CVDI03TPE CVDI71TPE CVDI72TPE CVDI73TPE CVDI01TPS CVDI02TPS CVDI03TPS CVDI71TPS CVDI72TPS CVDI73TPS

默克Millipore密理博Durapore滤芯CVHL72TP3 CVGL72TP3 CTGR71TP1

© bio-rad伯乐一级代理 |伯乐Aminex |伯乐电泳槽1658001| 伯乐ddPCR bio-rad授权代理商、biorad伯乐qpcr仪是专业的授权总代理区域代理经销平台。
© 如需询价,请加客服QQ:1749072012 、客服微信:jinshanbio,或发送邮件到1749072012@qq.com
© 平台为生命科学研究相关领域提供一站式耗材试剂仪器解决方案和采购服务,数据资源基于CC协议。
© 本文地址:https://gibcohyclone.cn/thread-32051.htm
产品询价需求提交
返回
扫码添加客服微信,咨询产品报价