LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit LNK243,LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit-试剂- bio-rad伯乐一级代理 |伯乐Aminex |伯乐电泳槽1658001| 伯乐ddPCR bio-rad授权代理商、biorad伯乐qpcr仪

LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit LNK243,LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit

2024-10-22

LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit

货号：LNK243D650,LNK241D650

规格：3 Conjugations For 20µg Antibody,3 Conjugations For 200µg Antibody

价格：3910,6758

产品类型：流式抗体

品牌：Bio-Rad

物种：其它

宿主：其它

抗体亚型：其它

荧光染料：DyLight 650

产品详情
Reagents in the Kit	3 Vials LYNXTMRapid Plus lyophilized DyLight®650 mix1 Vial LYNXTMRapid Plus Modifier reagent1 Vial LYNXTMRapid Plus Quencher reagent
Preparing The Antibody	Pack Size: 3 Conjugations For 200µg AntibodyThe following buffer solutions are recommended for preparing the antibody:10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5.Do not use buffers containing nucleophilic components e.g primary amines and thiols since they may react with LYNXTMchemicals, and Thiomersal should also be avoided. Azide (0.02-0.1%), BSA (0.1-0.5%), EDTA, Glycerol (up to 50%), and common non-buffering salts and sugars have little or no effect on conjugation efficiency.It is recommended that 100-200ug antibody be used in each labelling reaction. For optimal results the antibody should be at a concentration of 1mg/ml, with a maximum volume of 100ul and a recommended antibody amount of 100ug. A maximum of 200ug of antibody can be used to obtain good quality conjugates as long as the maximum conjugation volume of 100ul is not exceeded. Antibody below 1mg/ml can still be used as long as the maximum volume is not exceeded. Using less than the recommended amount of antibody may result in unbound label, but this will be removed during subsequent application wash steps. Antibody below 0.5mg/ml should be concentrated before use with the kit.Pack Size: 3 Conjugations For 20µg AntibodyThe following buffer solutions are recommended for preparing the antibody:10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5.Do not use buffers containing nucleophilic components e.g primary amines and thiols since they may react with LYNXTMchemicals, and Thiomersal should also be avoided. Azide (0.02-0.1%), BSA (0.1-0.5%), EDTA, Glycerol (up to 50%), and common non-buffering salts and sugars have little or no effect on conjugation efficiency.It is recommended that 10-20ug antibody be used in each labelling reaction. For optimal results the antibody should be at a concentration of 1mg/ml, with a maximum volume of 10ul and a recommended antibody amount of 10ug. A maximum of 20ug of antibody can be used to obtain good quality conjugates as long as the maximum conjugation volume of 10ul is not exceeded. Antibody below 1mg/ml can still be used as long as the maximum volume is not exceeded. Using less than the recommended amount of antibody may result in unbound label, but this will be removed during subsequent application wash steps. Antibody below 0.5mg/ml should be concentrated before use with the kit.
Regulatory	For research purposes only
Guarantee	12 months from date of despatch
存储条件
This kit contains lyophilized hygroscopic components that are moisture-sensitive. This kit is shipped under ambient conditions with silica packets to avoid exposure to moisture. On receipt, Bio-Rad recommend that the kit is stored at -20℃ and protected from moisture. Storage in frost-free freezers is not recommended.This product should be stored undiluted. Avoid repeated freezing and thawing. Before opening, allow the components to reach room temperature to minimize condensation.
应用
Application Name	Verified	Min Dilution	Max Dilution
Conjugation	√
This product has been reported to work in the following applications. This information is derived from testing within our laboratories, peer-reviewed publications or personal communications from the originators. Please refer to references indicated for further information. For general protocol recommendations, please visit theantibody protocolspage. Instructions For Use 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25°C) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use. 1. To the antibody sample add 1ul of the Modifier reagent for every 10ul of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1ul of Quencher reagent for every 10ul of antibody used. Leave to stand for 30 minutes before use. 1. To the antibody sample add 1μl of the Modifier reagent for every 10ul of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use. 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use. 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use. 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.

技术参数

产品类型 Conjugation Kit

© bio-rad伯乐一级代理 |伯乐Aminex |伯乐电泳槽1658001| 伯乐ddPCR bio-rad授权代理商、biorad伯乐qpcr仪是专业的授权总代理区域代理经销平台。
© 如需询价，请加客服QQ：1749072012 、客服微信：jinshanbio，或发送邮件到1749072012@qq.com
© 平台为生命科学研究相关领域提供一站式耗材试剂仪器解决方案和采购服务，数据资源基于CC协议。
© 本文地址：https://gibcohyclone.cn/thread-41258.htm

特别声明：以上内容(如有图片亦包括在内)来源于授权厂家或网络，如有侵权，请联系删除，本平台不提供信息存储服务。

Notice: The content above (including the pictures if any)comes from authorized manufacturers or networks. In case of infringement, please contact to delete it. This platform does not provide information storage services.

产品询价需求提交

LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit LNK243,LYNX Rapid Plus DyLight®650 Antibody Conjugation Kit

相关推荐