LYNX Rapid APC-Cy7 Antibody Conjugation Kit® LNK134APCCY7 ,LYNX Rapid APC-Cy7 Antibody Conjugation Kit®

2024-10-22

LYNX Rapid APC-Cy7 Antibody Conjugation Kit®

货号:LNK134APCCY7,LNK133APCCY7,LNK132APCCY7,LNK131APCCY7

规格:3 Conjugations For 10µg Antibody,1 Conjugation For 1mg Antibody,3 Conjugations For 100µg Antibody,1 Conjugation For 100µg Antibody

价格:3128,9078,6375,3171

产品类型:抗体和染料

品牌:Bio-Rad

物种:其它

宿主:其它

抗体亚型:其它

荧光染料:APC-Cy7

产品介绍
LYNX Rapid APC-Cy7 Antibody Conjugation Kit®enables the rapid conjugation of a pre-prepared lyophilized mixture containing Allophycocyanin (APC)-Cy7 label to an antibody or protein. Activation of proprietary reagents within the antibody-label solution results in directional covalent bonding of APC-Cy7 to the antibody.The LYNX Rapid Conjugation kit® can be used to label small quantities of antibody/protein at near neutral pH, allowing a high conjugation efficiency with 100% antibody recovery.
产品详情
Reagents in the KitPack Size: 1 Conjugation For 100µg Antibody1 Vial of 100ug LYNX lyophilized APC-Cy7 mix1 Vial LYNX Modifier reagent1 Vial LYNX Quencher reagentPack Size: 3 Conjugations For 100µg Antibody3 Vials of 100ug LYNX lyophilized APC-Cy7 mix1 Vial LYNX Modifier reagent1 Vial LYNX Quencher reagentPack Size: 1 Conjugation For 1mg Antibody1 Vial of 1mg LYNX lyophilized APC-Cy7 mix1 Vial LYNX Modifier reagent1 Vial LYNX Quencher reagentPack Size: 3 Conjugations For 10µg Antibody3 Vials of 10ug LYNX lyophilized APC-Cy7 mix1 Vial LYNX Modifier reagent1 Vial LYNX Quencher reagent
Preparing The AntibodyPack Size: 1 Conjugation For 100µg Antibody, 3 Conjugations For 100µg AntibodyThe following buffer solutions are recommended for preparing the antibody:10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.Do not use buffers containing nucleophilic components e.g primary amines and thiols since they may react with LYNX chemicals. Azide (0.02-0.1%), EDTA, up to 50% Glycerol and common non-buffering salts and sugars have little or no effect on conjugation efficiency.For optimal results the antibody should be at a concentration of 1mg/ml, with a maximum volume of 100ul and a maximum antibody amount of 100ug. Antibody at a concentration of greater than 1mg/ml requires dilution. Antibody below 1mg/ml can still be used as long as the maximum volume is not exceeded. Using less than the recommended amount of antibody may result in unbound label, but this will be removed during subsequent application wash steps. Antibody below 0.5mg/ml should be concentrated before use with the kit.Pack Size: 1 Conjugation For 1mg AntibodyThe following buffer solutions are recommended for preparing the antibody:10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.Do not use buffers containing nucleophilic components e.g primary amines and thiols since they may react with LYNX chemicals. Azide (0.02-0.1%), EDTA, up to 50% Glycerol and common non-buffering salts and sugars have little or no effect on conjugation efficiency.For optimal results the antibody should be at a concentration of 1mg/ml, with a maximum volume of 1ml and a maximum antibody amount of 1mg. Antibody at a concentration of greater than 1mg/ml requires dilution. Antibody below 1mg/ml can still be used as long as the maximum volume is not exceeded. Using less than the recommended amount of antibody may result in unbound label, but this will be removed during subsequent application wash steps. Antibody below 0.5mg/ml should be concentrated before use with the kit.Pack Size: 3 Conjugations For 10µg AntibodyThe following buffer solutions are recommended for preparing the antibody:10-50mM amine-free buffer (e.g HEPES, MES, MOPS and phosphate) pH range 6.5-8.5, although moderate concentrations of Tris buffer (<20mM) may be tolerated.Do not use buffers containing nucleophilic components e.g primary amines and thiols since they may react with LYNX chemicals. Azide (0.02-0.1%), EDTA, up to 50% Glycerol and common non-buffering salts and sugars have little or no effect on conjugation efficiency.For optimal results the antibody should be at a concentration of 1mg/ml, with a maximum volume of 10ul and a maximum antibody amount of 10ug. Antibody at a concentration of greater than 1mg/ml requires dilution. Antibody below 1mg/ml can still be used as long as the maximum volume is not exceeded. Using less than the recommended amount of antibody may result in unbound label, but this will be removed during subsequent application wash steps. Antibody below 0.5mg/ml should be concentrated before use with the kit
AcknowledgementsThis product or portions thereof is manufactured under license from Carnegie Mellon University under U.S. Patent Number 5,268,486 and related patents. Cy and CyDye are trademarks of GE Healthcare Limited.
RegulatoryFor research purposes only
Guarantee12 months from date of despatch
存储条件
This kit contains lyophilized hygroscopic components that are moisture-sensitive. This kit is shipped under ambient conditions with silica packets to avoid exposure to moisture. On receipt, Bio-Rad recommend that the kit is stored at -20℃ and protected from moisture. Storage in frost-free freezers is not recommended.This product should be stored undiluted. Avoid repeated freezing and thawing. Before opening, allow the components to reach room temperature to minimize condensation.
应用
Application NameVerifiedMin DilutionMax Dilution
Conjugation
This product has been reported to work in the following applications. This information is derived from testing within our laboratories, peer-reviewed publications or personal communications from the originators. Please refer to references indicated for further information. For general protocol recommendations, please visit theantibody protocolspage.
  • Instructions For Use
  • 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25°C) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.
  • 1. To the antibody sample add 1ul of the Modifier reagent for every 10ul of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1ul of Quencher reagent for every 10ul of antibody used. Leave to stand for 30 minutes before use.
  • 1. To the antibody sample add 1μl of the Modifier reagent for every 10ul of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.
  • 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.
  • 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.
  • 1. To the antibody sample add 1μl of the Modifier reagent for every 10μl of antibody and mix gently.2. Pipette the mixed antibody-modifier sample directly onto the LYNX lyophilized mix and gently pipette up and down twice to resuspend.3. Replace cap onto vial and incubate at room temperature (20-25oC) for 3 hours, or overnight if preferred.4. After incubation, add 1μl of Quencher reagent for every 10μl of antibody used. Leave to stand for 30 minutes before use.

技术参数

产品类型 Conjugation Kit

© bio-rad伯乐一级代理 |伯乐Aminex |伯乐电泳槽1658001| 伯乐ddPCR bio-rad授权代理商、biorad伯乐qpcr仪是专业的授权总代理区域代理经销平台。
© 如需询价,请加客服QQ:1749072012 、客服微信:jinshanbio,或发送邮件到1749072012@qq.com
© 平台为生命科学研究相关领域提供一站式耗材试剂仪器解决方案和采购服务,数据资源基于CC协议。
© 本文地址:https://gibcohyclone.cn/thread-41280.htm
产品询价需求提交
返回
扫码添加客服微信,咨询产品报价